The easiest way to install is through Sublime Text console. The console can be found by typing
ctrl+` (Mac keyboard
^`) or from
View > Show Console. Console should open at bottom with a field to input characters. Now you can paste the following Python code there and press enter:
import urllib.request,os,hashlib; h = '2915d1851351e5ee549c20394736b442' + '8bc59f460fa1548d1514676163dafc88'; pf = 'Package Control.sublime-package'; ipp = sublime.installed_packages_path(); urllib.request.install_opener( urllib.request.build_opener( urllib.request.ProxyHandler()) ); by = urllib.request.urlopen( 'http://packagecontrol.io/' + pf.replace(' ', '%20')).read(); dh = hashlib.sha256(by).hexdigest(); print('Error validating download (got %s instead of %s), please try manual install' % (dh, h)) if dh != h else open(os.path.join( ipp, pf), 'wb' ).write(by)
More from packagecontrol.io
This code creates the Installed Packages folder for you (if necessary), and then downloads the Package Control.sublime-package into it. The download will be done over HTTP instead of HTTPS due to Python standard library limitations, however the file will be validated using SHA-256.
If you would rather manually install Package Control for Sublime Text 3 that can be done too!
Sublime Text > Preferences > Browse Packages
/Users/jack/Library/Application Support/Sublime Text 3/Packages/
/Users/jack/Library/Application Support/Sublime Text 3and then into
Within CentOS, RHEL or Fedora you can configure your network interfaces by using configuration files located in /etc/sysconfig/network-scripts/. For each network interface say eth0 or eth1 there should be a corresponding configuration file such as ifcfg-eth0 or ifcfg-eth1 in the directory. Check out the directory yourself.
You can see here there is a configuration file for eth0 named
ifcfg-eth0. Let’s check it out.
# cat ifcfg-eth0 DEVICE="eth0" BOOTPROTO=dhcp NM_CONTROLLED="no" PERSISTENT_DHCLIENT=1 ONBOOT="yes" TYPE=Ethernet DEFROUTE=yes PEERDNS=yes PEERROUTES=yes IPV4_FAILURE_FATAL=yes IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME="eth0"
This config is for a DHCP interface.
Here is a static assignment interface configuration:
# cat ifcfg-eth0 DEVICE="eth0" HWADDR="00:21:70:10:7E:CD" NM_CONTROLLED="no" ONBOOT="yes" BOOTPROTO=static # BOOTPROTO=dhcp IPADDR=10.18.1.203 NETMASK=255.255.255.0 # # the GATEWAY is sometimes in: /etc/sysconfig/network GATEWAY=10.16.1.1
Then common items such as the DNS servers and hostname may be optionally added in /etc/sysconfig/network
# cat /etc/sysconfig/network HOSTNAME=jack.test.com DNS1=10.18.1.203 DNS2=184.108.40.206 ## DNS2=220.127.116.11 SEARCH=test.com
So, to create second interface of a static IP let’s do this:
nano ifcfg-eth1 or
nano /etc/sysconfig/network-scripts/ifcfg-eth1 if you are not in network-scripts directory.
Paste your configuration and change network info to your needs:
DEVICE="eth1” HWADDR="00:21:70:10:7E:CD" NM_CONTROLLED="no" ONBOOT="yes" BOOTPROTO=static # BOOTPROTO=dhcp IPADDR=10.18.1.203 NETMASK=255.255.255.0 GATEWAY=10.16.1.1
Once you are all set with your configurations restart the network service:
service network restart
# service network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... done. [ OK ] Bringing up interface eth1: Determining IP information for eth1... done. [ OK ]
ifconfig will show you what your current network information is now.
ifconfig eth0 Link encap:Ethernet HWaddr 02:55:12:78:50:1d inet addr:10.18.1.15 Bcast:10.18.1.255 Mask:255.255.255.0 inet6 addr: fe80::1c73:bcff:fe62:f075/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6648 errors:0 dropped:0 overruns:0 frame:0 TX packets:4798 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1159836 (1.1 MiB) TX bytes:1624933 (1.5 MiB) Interrupt:160 eth1 Link encap:Ethernet HWaddr ca:2c:49:10:2e:d4 inet addr:10.19.1.154 Bcast:10.19.1.255 Mask:255.255.255.0 inet6 addr: fe80::c82c:49ff:fe10:2ed4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1863 errors:0 dropped:0 overruns:0 frame:0 TX packets:2373 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:612953 (598.5 KiB) TX bytes:328246 (320.5 KiB) Interrupt:159 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2773 errors:0 dropped:0 overruns:0 frame:0 TX packets:2773 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:759142 (741.3 KiB) TX bytes:759142 (741.3 KiB)
This will create a static IP on eth1.
Add the following while changing the IP address and netmask to your liking:
iface eth1 inet static
gpasswd -a frank sudo
If you do not have a SSH key pair then you will have to generate a new one.
Files that are created:
/Users/localuser/.ssh/id_rsa # private key / passphrase protected
/Users/localuser/.ssh/id_rsa.pub # public key
Enter a passphrase and save this password.
On the server
su - frank
chmod 700 .ssh
Type CTRL+O to save as that file name. Enter
To exit nano type CTRL+X. Also you can CTRL+X and Y to exit the file and save when prompted.
chmod 600 .ssh/authorized_keys
Exit as frank to go back to root user.
CTRL+X Y Enter
service ssh restart
I’ve been attempting to use the command New-ADServiceAccount in PowerShell to set up Managed Service Accounts but I always end up with an error in the end. I then found out that there needs to be a KDS root key. Next I found this website which stated to Add-KdsRootKey –EffectiveTime ((get-date).addhours(-10)); I was given this error:
On the Domain Controller go to Active Directory Sites and Services (dssite.msc).
Go to View and enable Show Services Node option.
Then on the left pane open Services > Group Key Distribution Service > Server Configuration node.
There should be an object named “Group Key Distribution Service Server Configuration” within this node. If it exsists then you are almost there getting this sucker working. As stated from dirteam.com, in order for the Group Key Distribution Service to operate it will need root keys. Well I have done this and I get the error that has likely brought you here. Further reading, in the Master Root Keys if there is no object you are to run Add-KdsRootKey -EffectiveImmediately command.
More research has found that the process is looking for Domain Controllers in the “Domain Controllers” container withing Active Directory. It appears that only one DC running the relevant operating system needs to be in the root of the Domain Controllers container.
Now the command “Add-KdsRootKey –EffectiveTime ((get-date).addhours(-10));” will run without a hitch. I have only a few DCs so running the command now rather than the normal 10 hours is what I chose here. No idea of the Guid needs to be secret or not.
Now I can run my original command “New-ADServiceAccount -Name SQL2012STsvc -DNSHostName “dc1” -Path “cn=Managed Service Accounts, dc=omg,dc=com” -enabled $true”